Wilkerson F37 Manual do Utilizador descarregar pdf

Installation & Service Instructions

83-719-000

Filter Models F35, F36, F37 & F43

with Variations and Accessories

ISSUED: August, 2011

Supersedes: July, 2011

Doc. #83719000, EN#110617, Rev. 3

Bowl guards are recommended for added protection of polycarbonate bowls

where chemical attack may occasionally occur.

WARNING

To avoid polycarbonate bowl rupture that can cause personal

injury or property damage, do not exceed bowl pressure or

temperature ratings. Polycarbonate bowls have a 150 PSIG

pressure rating and a maximum temperature rating of 125°F.

WARNING

To avoid unpredictable system behavior that can cause personal injury

and property damage:

• Disconnect electrical supply (when necessary) before installation,

servicing, or conversion.

• Disconnect air supply and depressurize all air lines connected to this

product before installation, servicing, or conversion.

• Operate within the manufacturer’s speciﬁed pressure, temperature,

and other conditions listed in these instructions.

• Medium must be moisture-free if ambient temperature is below

freezing.

• Service according to procedures listed in these instructions.

• Installation, service, and conversion of these products must be

performed by knowledgeable personnel who understand how

pneumatic products are to be applied.

• After installation, servicing, or conversion, air and electrical supplies

(when necessary) should be connected and the product tested for

proper function and leakage. If audible leakage is present, or the

product does not operate properly, do not put into use.

• Warnings and speciﬁcations on the product should not be covered by

paint, etc. If masking is not possible, contact your local representative

for replacement labels.

WARNING

FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THE

PRODUCTS AND/OR SYSTEMS DESCRIBED HEREIN OR RELATED

ITEMS CAN CAUSE DEATH, PERSONAL INJURY AND PROPERTY

DAMAGE.

This document and other information from The Company, its subsidiaries

and authorized distributors provide product and/or system options for further

investigation by users having technical expertise. It is important that you

analyze all aspects of your application, including consequences of any failure

and review the information concerning the product or systems in the current

product catalog. Due to the variety of operating conditions and applications for

these products or systems, the user, through its own analysis and testing, is

solely responsible for making the ﬁnal selection of the products and systems

and assuring that all performance, safety and warning requirements of the

application are met.

The products described herein, including without limitation, product features,

speciﬁcations, designs, availability and pricing, are subject to change by The

Company and its subsidiaries at any time without notice.

EXTRA COPIES OF THESE INSTRUCTIONS ARE AVAILABLE FOR

INCLUSION IN EQUIPMENT / MAINTENANCE MANUALS THAT UTILIZE

THESE PRODUCTS. CONTACT YOUR LOCAL REPRESENTATIVE.

CAUTION

Polycarbonate bowls and sight domes, being transparent and tough, are

ideal for use with Filters and Lubricators. They are suitable for use in normal

industrial environments, but should not be located in areas where they could

be subjected to direct sunlight, an impact blow, nor temperatures outside of

the rated range. As with most plastics, some chemicals can cause damage.

Polycarbonate bowls and sight domes should not be exposed to chlorinated

hydrocarbons, ketones, esters and certain alcohols. They should not be used

in air systems where compressors are lubricated with ﬁre-resistant ﬂuids

such as phosphate ester and diester types.

Metal bowls are recommended where ambient and/or media conditions are

not compatible with polycarbonate bowls. Metal bowls resist the action of

most such solvents, but should not be used where strong acids or bases

are present or in salt laden atmospheres. Consult the factory for speciﬁc

recommendations where these conditions exist.

TO CLEAN POLYCARBONATE BOWLS USE MILD SOAP AND WATER

ONLY! DO NOT use cleansing agents such as acetone, benzene, carbon

tetrachloride, gasoline, toluene, etc., which are damaging to this plastic.

Installation

1. Refer to WARNINGS and CAUTIONS.

2. Purge downstream air line of oil.

3. Install the unit with the air ﬂowing in the direction indicated by the

arrow on the body and / or the DP2 indicator.

4. The drain line connection is dependent on the type of drain that is

selected.

5. Maximum inlet pressure and operating temperature ratings are: units

with DP2 150 psig (10.3 bar) 150°F (66°C); units without DP2: 300

psig (20 bar) 150°F (66°C).

Maintenance

1. TO CLEAN OR REPLACE FILTER ELEMENT: Shut off air supply

andreduce pressure in the unit to zero, remove the 8 screws from the

ﬁlterhousing, unscrew the ﬁlter support and remove ﬁlter element.

a. IF THE UNIT HAS A RIGID FILTER ELEMENT: remove and clean

period-ically by tapping on a hard surface, and blowing off with air

blow gun.Torque element support to 8 ±1 FT.-LB. when replacing

element. Element should be cleaned/replaced when the DP2

pressure indicator iscompletely red or when the DP3 reads 7 psi

(0.5 bar).

2. When the bowl becomes dirty, clean by wiping with dry, clean cloth.

3. Before placing the unit in service, make sure that the bowl is properly

reinstalled, and securely bolted in place using the noted torque

speciﬁcations.

Repair Kits And Replacement Parts

Filter Element kit (F35)

(includes ﬁlter element, o-ring / gasket) ........................... FRP-95-505

Filter Element kit (F36)

(includes ﬁlter element, o-ring / gasket) ........................... FRP-95-506

Filter Element kit (F37F)

(includes ﬁlter element, o-ring / gasket) ........................... FRP-95-507

Filter Element Kit (F43)

(includes ﬁlter element, o-ring / gasket) ........................... FRP-95-508

Drain Plate Kits:

Drain Plate 9/16 diameter (use with internal automatic

mechanical ﬂoat drain no. P32KA00DA)... .......................GRP-95-391

Drain Plate (1/2 NPT) ......................................................GRP-95-393

Drain Plate (1/2 BSPP) ....................................................GRP-95-395

Bowl O-ring Kit (43F) ...........................................................GRP-95-290

Bowl O-ring Kit (35F) ...........................................................GRP-95-291

Differential Pressure Gauge ................................................ DP3-01-000

Differential Pressure Indicator (Standard) ........................... DP2-01-001

Differential Pressure Removal Cap Kit ................................GRP-95-022

Safety Guide

For more complete information on recommended application guidelines, see the

Safety Guide section of Pneumatic Division catalogs or you can download the

Pneumatic Division Safety Guide at: www.wilkersoncorp.com

Richland, MI 49083 Tel: (269) 629-5000

1 2

Installation 1
Maintenance 1

Resumo do Conteúdo

Página 1 - Maintenance

Installation & Service Instructions 83-719-000Filter Models F35, F36, F37 & F43 with Variations and AccessoriesISSUED: August, 2011 Supersede

Página 2

Automatic Electric Drain ValvesModel Number KitPort Size NPTVoltageOperating PressureWDV3-G14BL 1/2" 115 VAC 232 PSIGWDV3-G24BL 1/2" 230 VAC

Modelos relacionados F36 | F35 |

Comentários a estes Manuais

Sem comentários

Wilkerson F37 Manual do Utilizador

Consulte online ou descarregue Manual do Utilizador para Hardware Wilkerson F37. Wilkerson F37 User Manual Manual do Utilizador

Resumo do Conteúdo

Modelos relacionados F36 | F35 |

Comentários a estes Manuais

Manuais e produtos relacionados com Hardware Wilkerson F37