Wilkerson SF2 Manual do Utilizador descarregar pdf

Installation & Service Instructions:

83-948-000

SF1 & SF2 Particulate Filters

ISSUED: May, 2008

Supersedes: August, 2006

Doc.# 83948000, EN# 080328, Rev. 5

Symbols

Installation

1. The ﬁlter should be installed with reasonable accessibility for

service whenever possible – repair service kits are available.

Keep pipe or tubing lengths to a minimum with inside clean

and free of dirt and chips. Pipe joint compound should be used

sparingly and applied only to the male pipe – never into the

female port. Do not use PTFE tape to seal pipe joints – pieces

have a tendency to break off and lodge inside the unit, possibly

causing malfunction. Also, new pipe or hose should be installed

between the ﬁlter and equipment being protected.

2. The upstream pipe work must be clear of accumulated dirt and

liquids.

3. Select a ﬁlter location as close as possible to the equipment

being protected and upstream of any pressure regulator.

4. Install ﬁlter so that air ﬂows in the direction of arrow on body.

5. Install ﬁlter vertically with bowl drain mechanism at the bottom.

Free moisture will thus drain into the sump “quiet zone” at the

bottom of the bowl.

Introduction

Follow these instructions when installing, operating, or servicing

the product.

Application Limits

These products are intended for use in general purpose

compressed air systems only.

Maximum Recommended Pressure Drop:

kPa PSIG bar

Particulate Filter 70 10 0.7

Operating Pressure Maximum kPa PSIG bar

Bowl w/ Twist Drain / No Sight Gauge 2068 300 21.0

Bowl w/ Autodrain / No Sight Gauge 1210 175 12.1

Bowl w/ Twist Drain and Sight Gauge 1700 250 17.0

Bowl w/ Autodrain and Sight Gauge 1210 175 12.1

Operating Temperature Range:

SF1 –

Manual Twist Drain 0°F to 180°F (-18°C to 82°C)

Auto Pulse Drain 32°F to 150°F (0°C to 66°C)

SF2 –

Manual Twist Drain (D) 0°F to 180°F (-18°C to 82°C)

Manual Twist Drain (W) 0°F to 150°F (-18°C to 66°C)

Automatic Float Drain 32°F to 150°F (0°C to 66°C)

Note: Air must be dry enough to avoid ice formation at temperatures

below 32°F (0°C).

Richland, MI 49083 Tel: (269) 629-5000

WARNING

To avoid unpredictable system behavior that can cause personal injury

and property damage:

• Disconnect electrical supply (when necessary) before installation,

servicing, or conversion.

• Disconnectairsupplyanddepressurizeallairlinesconnectedtothis

product before installation, servicing, or conversion.

• Operatewithinthemanufacturer’s specied pressure,temperature,

and other conditions listed in these instructions.

• Medium must be moisture-free if ambient temperature is below

freezing.

• Serviceaccordingtoprocedureslistedintheseinstructions.

• Installation, service, and conversion of these products must be

performed by knowledgeable personnel who understand how

pneumatic products are to be applied.

• Afterinstallation,servicing,orconversion,airandelectricalsupplies

(when necessary) should be connected and the product tested for

proper function and leakage. If audible leakage is present, or the

product does not operate properly, do not put into use.

• Warningsandspecicationsontheproductshouldnotbecoveredby

paint, etc. If masking is not possible, contact your local representative

for replacement labels.

WARNING

FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THE

PRODUCTS AND/OR SYSTEMS DESCRIBED HEREIN OR RELATED ITEMS

CAN CAUSE DEATH, PERSONAL INJURY AND PROPERTY DAMAGE.

This document and other information from The Company, its subsidiaries

and authorized distributors provide product and/or system options for further

investigation by users having technical expertise. It is important that you

analyze all aspects of your application, including consequences of any failure

and review the information concerning the product or systems in the current

product catalog. Due to the variety of operating conditions and applications for

these products or systems, the user, through its own analysis and testing, is

solely responsible for making the ﬁnal selection of the products and systems

and assuring that all performance, safety and warning requirements of the

application are met.

The products described herein, including without limitation, product features,

speciﬁcations, designs, availability and pricing, are subject to change by The

Company and its subsidiaries at any time without notice.

EXTRA COPIES OF THESE INSTRUCTIONS ARE AVAILABLE FOR INCLUSION

IN EQUIPMENT / MAINTENANCE MANUALS THAT UTILIZE THESE PRODUCTS.

CONTACT YOUR LOCAL REPRESENTATIVE.

Safety Guide

For more complete information on recommended application

guidelines, see the Safety Guide section of Pneumatic Division

catalogs or you can download the Pneumatic Division Safety

Guide at: www.wilkersoncorp.com

Automatic

Drain

Filter

w/Manual

Drain

1 2

Resumo do Conteúdo

Página 1 - below 32°F (0°C)

Installation & Service Instructions: 83-948-000SF1 & SF2 Particulate FiltersISSUED: May, 2008 Supersedes: August, 2006Doc.# 83948000, EN# 08

Página 2 - Service Kits Available

SF1 & SF2 Particulate Filters 83-948-000Operation1. Both free moisture and solids are removed automatically by the ﬁlter. 2. Manual drain ﬁlt

Modelos relacionados SF1

Comentários a estes Manuais

Sem comentários

Wilkerson SF2 Manual do Utilizador

Consulte online ou descarregue Manual do Utilizador para Hardware Wilkerson SF2. Wilkerson SF2 User Manual Manual do Utilizador

Resumo do Conteúdo

Modelos relacionados SF1

Comentários a estes Manuais

Manuais e produtos relacionados com Hardware Wilkerson SF2