Wilkerson L12 Manual do Utilizador descarregar pdf (Página 2)

1/4" and 3/8" L12 Atomist Lubricators 83-955-000

Polycarbonate

Bowl

(See Warning)

(Do Not Scratch

Internal Surfaces)

Retaining Collar

(Hand Tighten

Plus 1/4 Turn)

Bowl Guard

Metal Bowl

(Sight Glass

Shown)

Manual

Drain

Body Force Fill Adapter Kit

LRP-96-302

Bowl Force Fill Adapter Kit

LRP-96-304

Fill Button Assemb

Torque:

2.8 to 3.4Nm

(35 to 30 in. lbs.)

O-ring

Body Force

Fill Adapter

(Hand Tight)

Fill Button Assemb

Torque:

2.8 to 3.4Nm

(35 to 30 in. lbs.)

O-ring

Filter Body

(Internal

Surfaces)

O-ring

-ring

Fill Plug

Seal

Siphon Tube

Seal

Sight

Dome

Flapper

Service Kits Available

L12

Description

1/4" and 3/8"

Adjustment Knob LRP-96-300

Bowl Guard Kit GRP-96-345

Drip Control (Polycarbonate)

LRP-96-307

and Fill Plug Kit

Lubricator Repair Kit LRP-96-309

Body Force Fill Adaptor Kit LRP-96-302

Sight Dome Kit LRP-96-301

Sight Gauge Kit GRP-96-346

Metal Bowl Kits

Manual Drain GRP-96-348

Piston Drain GRP-96-353

Sight Gauge and

GRP-96-349

Manual Drain

Sight Gauge and

LRP-96-305

Force Fill Adapter

Polycarbonate Bowl Kits

Manual Drain GRP-96-347

Bowl Force Fill Adapter Kit LRP-96-304

Drain Kits

Manual Drain GRP-96-340

Downstream Delivery DPM

33 67 100

133

167 200 23

Dome Drip Rate DPM

Oil Delivery Conversion

3% of Drip Rate to Downstream

3. Oil delivery adjustment — To adjust oil delivery, turn

adjustment knob on top of the lubricator.

Leaner — Clockwise

Richer — Counterclockwise

By counting the number of drops per minute in the sight

dome, you can adjust to your requirements.

Atomist lubricator — Approximately 3% of the droplets visible

in the sight dome go downstream; adjust drip rate accordingly.

Consult oil delivery conversion chart.

Generally, one drop per minute downstream for every

10 - 15 SCFM flow is satisfactory.

25 drops per minute equals one (1) ounce per hour - volume

of oil passing through the sight dome.

NOTE: This is a constant density type lubricator which delivers a constant

ratio of oil to air flow. Therefore, if air flow increases or decreases, oil

delivery will be adjusted proportionately. ONLY IF A DIFFERENT RATIO

IS DESIRED SHOULD YOUR ADJUSTMENT KNOB SETTING BE

CHANGED AFTER YOUR INITIAL SETTING.

4. To replace fill plug, drip control, and service lubricator:

A. Turn off air supply and depressurize the unit.

B. Refer to pictorial for servicing and torque values.

C. Turn on air supply and check lubricator for leakage. If

leakage occurs, DO NOT OPERATE — conduct repairs

again.

Lightly grease with provided lubricant. (Silicone free)

Inspect for nicks, scratches, and surface imperfections.

If present, reduced service life is probable and future

replacement should be planned.

Clean with lint-free cloth.

1 2 3 4 5 6

Comentários a estes Manuais

Sem comentários

Wilkerson L12 Manual do Utilizador Página 2

Comentários a estes Manuais

Manuais e produtos relacionados com Hardware Wilkerson L12